Netgear Router Troubleshooting Lights

Netgear Wi-Fi router is a reliable and efficient device for setting up a network of devices.The LED lights on the Wi-Fi router notifies the specific errors based on different light spotting signals.Each error can be identified quickly based on the colors indicated on the Wi-Fi router setup. Troubleshooting the router lights blinking issues is a straightforward and hassle-free process if you follow the right steps.

How To Fix Netgear Router Orange Light

In general, the orange light turns into solid green or white after twenty or thirty seconds. But if it remains orange, then it indicates a technical problem with your Wi-Fi router or modem connections.

Carry out these steps to fix the Netgear router orange light issues:

  • Step 1:Check whether the connections are set up appropriately.
  • Step 2:Turn off all the devices and Restart your Wi-Fi router after ten seconds.
  • Step 3:Connect your router to a different electrical outlet and change the existing Netgear adapter.
  • Step 4:Check the Firmware Version of your Netgear router because using an obsolete version of the Netgear router may also be the cause of this issue.
  • Step 5:In some cases, you cannot access the Internet due to this issue. At that time, connect your computer directly to the modem and update the firmware for the Netgear router. 
  • Step 6:If the problem persists, reconfigure the Wi-Fi router after performing the factory reset in the Netgear router.

Internet Light Not On Netgear Router

  • Step 1:If the Wi-Fi on your Netgear router is disabled, then there is a chance for this issue to occur.
  • Step 2:To check it, navigate to your Netgear router’s setup page.
  • Step 3:Check if the Enable Wireless Router Radio and Enable SSID Broadcast options are checked.
  • Step 4:Make sure that your Netgear router’s firmware is updated.
  • Step 5:If this issue persists even now, then perform a factory reset on your Netgear router and check if the problem is resolved.
  • Step 6:If the Wi-Fi light is not turning ON while using the Ethernet connection, then check if the Ethernet connectivity at the modem or computer and the router.
  • Step 7:Check if the computer or modem is switched ON.
  • Step 8:Make sure that the Ethernet cable is not damaged.
  • Step 9:If yes, replace the damaged cable with a new one.
  • Step 10:The Wi-Fi light not turning ON issue also occurs when the router has internal damage.
  • Step 11:To get remote assistance, contact our technical support by clicking the Call button available on this screen.

Netgear Router All Lights Flashing

Problem 1 - Power LED blinking amber


  • Step 1:Check the Reset button. If the Reset button is pressed, release it to resolve this Power LED blinking error.
  • Step 2:Download the Netgear router’s firmware on your computer.
  • Step 3:If you have already installed the firmware, update it.

Problem 2 - Internet LED blinking white

  • Step 1:This indicates that the data transfer is in progress.
  • Step 2:As soon as the data transfer completes, the internet LED stops to blink.

Problem 3 - USB LED blinking

  • Step 1:This occurs when USB is connected to the Netgear router, and it tries to establish a connection.
  • Step 2:The USB LED stays green or white when the USB connection is successful.

Netgear Router Red Light

Irrespective of which LED stays red, try to power cycle both your Netgear router and modem.

Power Cycle

Disconnect all the cables that are attached to the Netgear router and modem.After some time, reconnect the cables to them. 

1. Problem - LED turns red once you perform the Netgear router setup Solutions

  • Step 1:Access the Netgear router’s web-based setup page using the correct login credentials.
  • Step 2:Navigate to the Wireless Settings section.
  • Step 3:Enable the 2.4GHz to 5.0GHz network range.
  • Step 4:Make sure the remaining wireless settings are appropriate.

2. Problem - Red LED blinks on a new Netgear router Solutions

  • Step 1:This issue can be resolved if you perform the Netgear router setup as per the manual instructions.
  • Step 2:Check for the available firmware update of the Netgear router. If any update is available, install it.

3. Problem - Power LED blinks red after turning on the Netgear router Solutions

  • Step 1:First, you have to restart the Netgear router.
  • Step 2:Make sure to reset the Netgear router to the default factory settings.
  • Step 3:If the red LED still blinks, connect your computer to the Netgear router’s LAN port.
  • Step 4:Change the dynamic settings to static by setting the IP address, subnet mask, and gateway.
  • Step 5:After setting the static IP address, open the Command Prompt window on your Windows computer. If you are using Mac, then open the Terminal window.
  • Step 6:In the Command/Terminal window, enter ‘ping IP X’ without including single quotes. Note: The letter X denoted here is the static IP address).
  • Step 7:Check if you are receiving replies in the Command window. 
  • Step 8:If so, the issue is resolved. If the problem persists, update the Netgear router’s firmware.
  • Step 9:Now, restart the Netgear router.

Netgear Router Blinking Orange Internet Light

The orange internet light that is blinking on a router means the router is starting a network connection and trying to obtain an IP address. After a few minutes, this flashing orange light will turn to a green light indicating a secured connection. Suppose it did not turn green, then there is some trouble with the router connection. To fix the problem, refer to the next issue.

Netgear Router Yellow Internet Light

When the yellow internet light is steadily glowing on the Netgear router, it indicates that the router has network issues when connected to the devices.Wait for some time and check if the internet light is changed to green. If it does not change, then attempt the following steps;

  • Step 1:Switch off the router and restart it. See if the router works.
  • Step 2:If it doesn’t, check if the internet settings of the router are correct.
  • Step 3:Rectify the wrong internet settings for a better network connection.

Netgear Router No Internet Light

If the internet light on the Netgear router is turned off, then the network connection is not established. To resolve this issue, try the given measures;

  • Step 1:If you have connected the networking devices and the computer using an Ethernet cable, check if the cable connections are intact.
  • Step 2:Using other cables can lead to insecure connections. So use only the standard Ethernet cables for connecting the devices. 

Netgear Router Internet Light Blinking Green

The flashing green internet light on a Netgear router denotes that the router is processing data or sending/receiving data at an optimized speed. The router does not have any network or connection issue if it is regularly working.